Saflok 410® is a concealed fix profile with an effective cover width of 410mm. It is an angular interlocking trapezoidal rib profile and can be roll-formed on-site.

SAMPLE SPECIFICATION

Safintra 0,50mm thick Saflok 410® Colorplus® AZ150 interlocking roof sheeting fixed to steel internal purlins at 1700mm centres, and ridge/eaves purlins at 1500mm centres using Saflok 410® clips that must be fastened to steel purlins with Fixtite™ or Safintra approved wafer head self-tapping screws, all in accordance with manufacturer’s recommendations.

The sheeting will be a double interlocking concealed fix Saflok 410® as manufactured by Safintra, roll-formed in continuous lengths from Aluminium or Aluminium-Zinc coated steel.

The profile shall be roll-formed with 3 ribs at centres not exceeding 205mm and a cover width of 410mm. The male rib is to include spurs to ensure a double interlocking action with adjacent sheets. The minimum rib height shall be 41mm. Two stiffening ribs are incorporated in each pan.

Note 1
Saflok 410® can be curved or bullnosed to a minimum internal radius of 450mm. Reverse cranking is not possible.

MATERIAL OPTIONS

NOTE 2

Note that when using Aluminium material on galvanized steel purlins, the use of an isolation tape or similar to prevent the bridging of the two dissimilar materials is recommended. Should the two metals have direct contact it will ultimately result in the manifestation of galvanic corrosion, and the service life of the aluminium will be compromised.

Material and coating thickness can vary regionally. Consult your local Safintra branch for availability.

 

PURLIN SPACING & DRAINAGE

Span tables are for Saflok 410® with light foot traffic only. It is based on 1.5kN downward load and 2kPa negative wind loading. The span table below refers to the maximum recommended spans. For further information, consult Safintra’s Technical Department and SANS 10160-3.

*0.80 Aluminium-Zinc Material is rolled in G275.

Saflok 410® clips are calculated at 145g per clip – You will require approximately 3 clips per m².

The anchor mechanism of the Saflok 410® Clip is design registered with South African Design Appl. No. F2017/00456*

*refer to the Safintra Technical Department for more information​

Cranking

Saflok 410® sheets may be cranked and bull-nosed but not reverse cranked. The minimum radius is 450mm. On-site cranking is available on request.

Curving

Natural springing occurs at a 36m radius in the convex and at a 60m radius in the concave. It is important to reduce purlin spacing’s by 20% when spring curving a roof. Oil canning may be expected.

LENGTH AND ROOF PITCH

Saflok 410® can be ordered in any practical length as per customer requirements. On-site rolling is recommended for lengths in excess of 13.2 metres, limited by space constrictions and building design. The minimum roof pitch when using Saflok 410® is 2° on steel and 3° on timber. Clip-in marks and oil canning might be visible on high pitched roofs or vertical applications. This visual effect might not be aesthetically pleasing in a residential application.

Rolling straight onto a roof

It is possible to roll-form straight onto a roof using a scaffold ramp. The limitations are the building height and space needed to roll. A departure angle of 10° is the maximum allowed at any time. A  greater angle would damage the sheet when leaving the mill and again when bending to settle onto the roof.

Dimensional tolerances

A length variation range of +10mm and -0mm, and a width tolerance of ±3mm is permissible.

FIXING GUIDE

FASTENERS

Where insulation is to be installed, you may need to increase the length of the fasteners given below, depending on the density and thickness of the insulation and spacer.
When the fastener is properly tightened:
• Into metal: There should be at least three threads protruding past the purlin you are fixing to, but the shank guard must not reach that purlin.
• Into timber: The fastener must penetrate the timber by at least 30mm.

NOTE 4
Please note that clips can be manafactured in alternative metals  to ensure metal compatability.

SAFLOK 410  CLIP

The fully interlocking Saflok 410® clip incorporates one anchor to clasp the middle rib and a dual-action gooseneck to positively hold down the male-female joint.

  • Provides full-width engagement on the gooseneck-male rib joint.
  • The Saflok 410® clip demonstrates an excellent hold down capability in negative wind uplift load tests.
  • Engineer-designed geometry of the anchor unit for optimal performance under high wind loads and foot traffic.
  • Entire clip is manufactured from 0.8mm Aluminium-Zinc coated steel for compatibility with sheeting.

SAFLOK 410® INSTALLATION

  • Starting with the female rib first, align the first row of clips and fasten on all five fastening positions.
  • Lay the first sheet down over the clips. Starting at the eave side, clip the sheet onto the clips by first engaging the anchors and then engaging the female rib over the gooseneck and male rib.
  • Engage the gooseneck of the next row of clips over the male rib and fasten on all five fasteners. Repeat from step 2.

NOTE 3
Concealed fix side cladding must be pierced fixed for prevention of sheet movement due to gravity. Pierce fix the bottom and top of the sheets.  Internal pierce fixing may be necessary on longer sheets. Cladding is to be fixed in the pan of the sheet with #12x25mm Fixtite™ Fasteners  - Class 4 only.

NOTE 5
During installation, clean the roof daily by removing all swarf, pop rivets and unused fasteners or any other debris

SPECIALISED FIXING ACCESSORIES
HIGH WIND LOAD INSTALLATION DETAILING  (HIGH WIND ZONES AND COASTAL WIND BELTS)

​Polysliders are specifically designed for polycarbonate or fibreglass sheeting and allow for a large amount of thermal expansion. The components are designed to work in conjunction with a saddle washer which is positively fixed to the sliding bracket. This clip is also used for Saflok 410® sheeting around the perimeters and exposed areas of the building, where high wind load conditions prevail.

Overhangs are prone to a build-up of wind pressure and are considered to be the weak point of any roof. All overhangs larger than 500mm need to be positively fixed with a saddle washer to allow for expansion and contraction. These include canopies, walkways, lean-to roofs, loading bays and decorative roofs.

  1. Align the first row of the Polyslider baseplates and fasten through the pre-drilled holes in the two positions where the slider brackets attach.
  2.  Connect the slider brackets to the base plate and lay the first sheet over the slider brackets.
  3. Place saddle washers over the first three ribs above the purlin, and fasten the saddle washers through the ribs into the slider brackets.
  4. Place the next row of baseplates and fasten. Overlap the end fastening positions to self-align the row of baseplates. Repeat from step 2.

NOTE 7
All Polycarbonate sheet installations (including, but not limited to in-plane installations) with Safintra roofing/cladding profiles, should be done in accordance to SANS 10237:2017 (Annexure E Rooflights).

SAFLOK® SADDLE WASHER
The Saflok® saddle washer works with the Polyslider to positively fix the sheeting (polycarbonate or steel) onto the Polyslider clip without restricting thermal expansion. The saddle washers are cold bonded to a 3mm Ethylene Vinyl Acetate (EVA) seal, which prevents ingress of water through the fastener hole.
POLYSLIDER 410 CLIP | HIGH WINDLOAD CLIP
The polyslider clip consists of a baseplate and three slider brackets.

NOTE 6
The saddle washer can only be fixed from the top.

SPECIALISED FLASHING INSTALLATION

Safintra recommends the use of Flashing Slider Brackets for very long sheets. Please consult our Technical Department for assistance.

F10 BRACKET FOR FLASHINGS

F10 brackets are used to fix flashing onto Saflok® profiles without drilling directly into the sheet. The bracket allows for minimal expansion.

NOTE 8
This clip is positively fixed. Care should be taken when detailing industrial length sheeting and flashings due to thermal expansion.

F10 Bracket for longitudinal flashings on Saflok® profiles.

F10 Bracket for transverse flashings on Saflok® profiles.

 CLIP-ON SLIDERS FOR FLASHINGS

The clip-on slider clips onto the rib of the Saflok profile to fix longitudinal flashing (Barge, Sidewall) to the sheeting without the need for fasteners piercing the sheet. The clip will allow for more thermal expansion that the F10 bracket.

Clip-on Slider bracket for longitudinal flashings on Saflok profiles.

 2-PIECE SLIDER FOR FLASHINGS

The 2-piece sliders are used to fix transverse flashings (Apex, Ridge, Headwall) to the sheeting without drilling directly into the sheet. This bracket will allow for up to 50mm of thermal expansion.

2-piece Slider bracket for transverse flashings on Saflok profiles.

SAFLOK STARTER BRACKET

The Saflok starter bracket is used to secure the first and/or last rib of the edge sheet without restricting thermal expansion.

SAFLOK 410 LIPPING & BENDING TOOL

The bending tool is used to bend the pan up on the ridge side of the sheet to create a water barrier (Also known as the tanking or turning up of the sheet.) The lipping tool is used on the eave side of the sheet to create a turned down lip (Also known as the tanking or turning down of the sheet.)

Saflok 410 bending tool application

Saflok 410 lipping tool application

Design My Home

Specification Tool

i

Spec Sheet

h

Specification Manual

h

Product Guide

n

CAD Download

m

Revit Download

Enquire Now

Design My Home

Specification Tool

i

Spec Sheet

h

Specification Manual

n

CAD Download

h

Product Guide

m

Revit Download

We’re building our future

New Sales Offices now open in George, East London and Mthatha